![]() Mac ─ If your Mac is in a Sleep state, Splashtop 2/Personal/Business can awaken it to a “waiting for login” screen (via the “Wake-on-LAN” feature). Currently, it is not possible to awaken a Mac computer from a powered-off state via the WoL feature.* On Windows 8 or 10, you need to disable "Turn on fast startup" function to be able to wake it up from powered off state. PC ─ If your PC is in a Sleep, Hibernate, or powered-off state, Splashtop 2/Personal/Business can awaken it to a “waiting for login” screen via the “Wake-on-LAN” feature.Wake-on-LAN usage timing and limitations: You could also use the checking tool to make sure the settings are correct.There might be times when you will need to tap the Wake up this computer button several times instead of only one time, to ensure that the computer has been awakened.Tap on the button to attempt to wake up the PC computer from either a Powered-off, Sleep or Hibernation state or a Mac computer from a Sleep state. Tap the "Edit" button to find Wake up or Wake computer button will display, as shown above.ĥ. You should see the computer you want to awaken shown as an unavailable one (gray computer icon), like the example shown in the illustration below.Ĥ. Keep your computer ON, and make a successful connection, then shut down your computer (power off).ģ. On your Splashtop apps, or on the web portal (my.).Ģ. Steps required to wake your computer from Sleep or Hibernation mode:ġ. If you are using only battery power on the laptop, this may cause an attempt to use the WoL feature to fail. If your computer is a laptop (for example, a NB, Mac Book Pro or Mac Book Air), please make sure the power cable is plugged in to an electrical power source. ![]() Your computer must be connected to your wireless router using the network cable (Ethernet).Ĥ. Make sure the Wake for network access option is selected in the Energy Saver settings.ģ.Configure your LAN network interface adapter ( Control Panel -> Device Manager -> Network adapters).Enable Wake-on-LAN in the system BIOS if you want to allow your computer to wake from a powered-off (i.e., Hibernate) state.For example, it might be "Wake on LAN," or "Onboard LAN Boot ROM," or something else. Please note that the term in BIOS might vary. Configure your computer to be Wake-on-LAN ready. (This step pertains to PC only Mac users can ignore this.)Ģ. Make sure your BIOS supports Wake-on-LAN, and that this option has been enabled. To connect to your computer when it is in Sleep or Hibernation mode, you need the following:ġ. (New) On Windows 8 or 10, you need to disable "Turn on fast startup" function to be able to wake it up from powered off state. Please note that currently, it is not possible to awaken a Mac computer from a powered-off state via the WoL feature, although it can be done from a sleeping state as described below. Have an awake computer on the same network as the sleeping/off computer AND that awake computer has Streamer 3.0.8.3 or newer installed and logged into your account.The computer is connected by Ethernet, not WiFi.Settings in Windows or Mac have been properly set up.PC BIOS supports WoL and that the option has been enabled.Otherwise, there is no chance to make WoL work successfully. * Business Access Solo and Remote Support Basic plans do not include remote wake and remote reboot features.įirst, we ask that you make sure the following four conditions have been satisfied completely. In this topic, we provide the instructions. However, this is not an intuitive feature, and is performed using somewhat complicated settings. I could Static them, but really the only thing affected by it is iTALC, and I'm the only one in the building using it.Splashtop Business Access Pro/Performance, Remote Support* and Splashtop Personal (formerly known as Splashtop 2) provide a method to perform Wake-on-LAN (WoL) which is similar to Splashtop v1.x. obviously, we expect this to be fixed when we have all 20 logging on at once. It's usually fine when every computer is running daily, but we're now setting up 20 tablets, and since we only image and set up 7 at a time, sometimes there's a gap between setups and a newer one gets an older one's IP. The only problem I have with iTALC (and it's a Windows Server thing) is duplicate entires in the forward lookup zones for DHCP addresses. I don't think we'll switch though, as iTALC is functioning very well now that school's back running. LanView3 looks good too, I had iTALC rolled out from a custom-compiled source before noticing LV3. Just have to get a list of MAC addresses from the computers and put them in the config box for that box in iTALC, then I can just wake them up from anywhere. I user iTALC for waking up, shutting down, rebooting, etc.
0 Comments
Leave a Reply. |